WEAR LOAD CAPACITY OF CROSSED HELICAL GEARS

Aleksandar Miltenović, Milan Banić, Jovan Tanasković, Jelena Stefanović-Marinović, Damjan Rangelov, Marko Perić

DOI Number
https://doi.org/10.22190/FUME220114015M
First page
125
Last page
138

Abstract


The paper presents a wear load capacity of crossed helical gears (gear pair consists of a worm and a helical gear). Crossed helical gears are similar to worm gear pairs, and it is logical to extend the load capacity calculation approach of worm gears for the case of crossed helical gears. One of the disadvantages of crossed helical gear sets is very high running-in wear. The paper explains the transition between running-in and steady-state wear and proposes a joint wear calculation model. The paper outlines a proposal to extend the calculation method for wear load capacity from a worm gear pair to the case of crossed helical gears (a worm with a helical gear). This calculation method for determining the wear load capacity of crossed helical gears is verified for the cases when the wheel is of bronze CuSn12Ni2-C-GCB and sintered steel Fe1.5Cr0.2Mo.


Keywords

Crossed Helical Gears, Wear, Bronze, Sintered Steel, Load Capacity

Full Text:

PDF

References


Xue, Q., Zhang, X., Geng, C., Teng, T., 2021, Gear shift coordinated control strategy based on motor rotary velocity regulation for a novel hybrid electric vehicle, Applied Sciences, 11(24), 12118.

Wang, A., Li, Y., Du, X., Zhong, C., 2021, Diesel engine gearbox fault diagnosis based on multi-features extracted from vibration signals, IFAC-PapersOnLine, 54(10), pp. 33-38.

Marinković, Z., Marinković, D., Petrović, G., Milić, P., 2013, Modelling and simulation of dynamic behaviour of electric motor driven mechanisms, Tehnicki Vjesnik, 19(4), pp. 717-725.

Vullo, V., 2020, Gears - Volume 1: Geometric and Kinematic Design, Springer Nature Switzerland AG, Switzerland.

Vullo, V., 2020, Gears - Volume 2: Analysis of Load Carrying Capacity and Strength Design, Springer Nature Switzerland AG, Switzerland.

Shilko, E., Grigoriev, A., Smolin, A., 2021, A Discrete Element Formalism for Modelling Wear Particle Formation in Contact Between Sliding Metals, Facta Universitatis-Series Mechanical Engineering, 19(1), pp. 7-22.

Cao, H., Tian, Y., Meng, Y., 2021, A Fracture-Induced Adhesive Wear Criterion and Its Application to the Simulation of Wear Process of the Point Contacts under Mixed Lubrication Condition, Facta Universitatis-Series Mechanical Engineering, 19(1), pp. 23-38.

Wagner, J.J., Jenson, D.A., Sundararajan, S., 2017, The effect of contact pressure and surface texture on running-in behavior of case carburized steel under boundary lubrication, Wear, 376-377, pp. 851–857.

VDI 2726 2736 Blatt 3, 2012, Thermoplastische Zahnräder, Schraubradgetriebe, Paarung Zylinderschnecke Schrägstirnrad, Tragfähigkeitsberechnung, Beuth Verlag, Berlin.

DIN 3996: Tragfähigkeitsberechnung von Zylinder­Schneckengetrieben mit sich rechtwinklig kreuzenden Achsen, 2012.

Wendt, T., 2008, Tragfähigkeit von Schraubradgetrieben mit Schraubrädern aus Sintermetall, Dissertation Ruhr-Universität Bochum.

Boehme, C., Vill, D., Tenberge, P., 2019, Enhanced application limits for crossed helical gearboxes using new geometries for smaller sliding paths or smaller contact pressures, Power transmission 2019, MATEC Web of Conferences, 287, 01010.

Norgauer, P., Sigmund, W., Kadach, D., Stahl, K., 2017, Comprehensive simulation methods for crossed helical gear sets with the main focus on the calculation of contact patterns, Forsch Ingenieurwes, 81, 299–306.

Liang, D., Meng, S., Tan, R., 2021, Mathematical model and characteristics analysis of crossed-axis helical gear drive with small angle based on curve contact element, Science progress, 104(2), pp. 1-19.

Octrue, M., 2014, Evolution of Worm Gear Standards and their Consequences on Load Capacity Calculation Approach, Power Transmission Engineering, 6, pp. 36-42.

Chernets, M.V., 2019, Prediction Method of Contact Pressures, Wear and Life of Worm Gears with Archimedean and Involute Worm, Taking Tooth Correction into Account. J. Frict. Wear, 40, pp. 342–348.

Daubach, K., Oehler, M., Sauer, B., 2021, Wear simulation of worm gears based on an energetic approach, Forsch Ingenieurwes.

Ivanov, A.S., Goncharov, S.Y., 2021, Wear and Efficiency of Worm Gears with Running-In. Russian Engineering Research, 41(8), pp. 697–700.

Weisel, C., 2018, Einfluss der Tragbildgröße und –lage auf den Wirkungsgrad und den Betriebsverschleiß bei Schneckengetrieben, FVA-Heft Nr. 853.

Miltenović, A., Nikolić, V., Banić, M., 2015, Wear Load Capacity of Crossed Helical Gears with Wheel Made from Sintered Steel, Science of Sintering, 47, pp. 153-163.

Miltenović, A., 2016, Damage types, Load Capacity and Efficiency of Crossed Helical Gears with Wheels from Sintered Steel, Theory and Practice of Gearing and Transmissions, Mechanisms and Machine Science, 34, pp. 189-232.

Miltenović, A., Nikolić, V., Milovančević, M., Banić, M., 2012, Experimental and FEM analysis of sintered steel worm gear wear, Transactions of FAMENA, 36(4), pp. 85-96.

Krol, O., Sokolov, V., 2022, Optimal Choice of Worm Gearing Design with Increased Wear Resistance for Machine's Rotary Table, Advanced Manufacturing Processes III, InterPartner 2021, Lecture Notes in Mechanical Engineering, Springer, pp. 3-12.

Predki, W., Miltenović, A., 2010, Influence of Hardening on the Microstructure and the Wear Capacity of Gears made of Fe1.5Cr0.2Mo Sintered Steel, Science of Sintering, 42, pp. 183-191.




DOI: https://doi.org/10.22190/FUME220114015M

Refbacks

  • There are currently no refbacks.


ISSN: 0354-2025 (Print)

ISSN: 2335-0164 (Online)

COBISS.SR-ID 98732551

ZDB-ID: 2766459-4