MULTILEVEL NUMERICAL MODEL OF HIP JOINT ACCOUNTING FOR FRICTION IN THE HIP RESURFACING ENDOPROSTHESIS

Galina M. Eremina, Alexey Yu. Smolin

DOI Number
https://doi.org/10.22190/FUME190122014E
First page
29
Last page
38

Abstract


Friction between the moving parts of the endoprosthesis has a significant impact on the endoprosthesis operation time. Primarily, it concerns the endoprosthesis of hip and knee joints. To improve the tribological characteristics of the metal endoprosthesis, hardening nanostructured coatings are used. Usually, titanium and titanium alloys are used as metal, and titanium nitride is used as a coating. Herein, we propose an approach to multilevel modeling of the system “bone-endoprosthesis” which is based on the movable cellular automaton method and accounts for friction between the moving parts of the hip resurfacing endoprosthesis. We validated the models of the friction system materials using the instrumented scratch test simulation. Then, we simulated friction at the mesolevel, explicitly considering roughness of the coating. The results obtained at the mesolevel were used as tribological characteristics of the coating in the macroscopic model of the hip resurfacing endoprosthesis.

Keywords

Hip Resurfacing Endoprosthesis, Coatings, Scratch Test, Friction, Simulation, Movable Cellular Automaton Method

Full Text:

PDF

References


Bitar, D., Parvizi, J., 2015, Biological response to prosthetic debris, World Journal of Orthopaedics, 6(2), pp. 172-89.

Sovak, G., Weiss, A., Gotman, I., 2000, Osseointegration of Ti6A14V alloy implants coated with titanium nitride by a new method, The Journal of Bone & Joint Surgery Series B, 82(2), pp. 290-296.

Gotman, I., Gutmanas, E.Y., Hunter, G., 2017, Wear-resistant ceramic films and coatings, Comprehensive Biomaterials II, pp.165-203.

Wu, S. J., Li, H., Wu, S. Y., Guo, Q. and Guo, B., 2014, Preparation of titanium carbide–titanium boride coatings on Ti6Al4V by PIRAC, Surface Engineering, 30(9), pp. 693-696.

Wu, S, Ma, S, Wu, S, Zhang, G, Dong, N., 2018, Composition, microstructure, and friction behavior of PIRAC chromium carbide coatings prepared on Q235 and T/P 24, International Journal of Applied Ceramic and Technology, 15, pp. 501–507.

Kot, M., Rakowski, W., Lackner, J.M., Major, T., 2013, Analysis of spherical indentations of coating-substrate systems: Experiments and finite element modeling, Materials and Design, 43, pp. 99-111.

Lofaj, F., Németh, D., 2017, The effects of tip sharpness and coating thickness on nanoindentation measurements in hard coatings on softer substrates by FEM, Thin Solid Films, 644, pp.173-181.

Marchiori, G., Lopomo, N., Boi, M., Berni, M., Bianchi, M., Gambardella, A., Visani, A., Russo, A., Marcacci, M., 2016, Optimizing thickness of ceramic coatings on plastic components for orthopedic applications: A finite element analysis, Materials Science and Engineering C, 58, pp. 381-388.

Bouzakis, K.-D., Michailidis, N., Hadjiyiannis, S., Skordaris, G., Erkens, G., 2002, The effect of specimen roughness and indenter tip geometry on the determination accuracy of thin hard coatings stress–strain laws by nanoindentation, Materials Characterization, 49(2), pp. 149-156.

Jiang, W.-G., Su, J.-J., Feng, X.-Q., 2008, Effect of surface roughness on nanoindentation test of thin films, Engineering Fracture Mechanics, 75(17), pp. 4965-4972.

Sliwa, A., Mikuła, J., Gołombek, K., Tanski, T., Kwasny, W., Bonek, M., Brytan, Z., 2016, Prediction of the properties of PVD/CVD coatings with the use of FEM analysis, Applied Surface Science, 388, Part A, pp. 281-287.

Skordaris, G., Bouzakis, K.D., Kotsanis, T., Charalampous, P., Bouzakis, E., Breidenstein, B., Bergmann, B., Denkena, B., 2017, Effect of PVD film's residual stresses on their mechanical properties, brittleness, adhesion and cutting performance of coated tools, CIRP Journal of Manufacturing Science and Technology, 18, pp. 145-150.

Zlotnikov, Ig., Dorogoy, A, Shilo, D., Gotman, I., Gutmanas, E., 2010, Nanoindentation, modeling, and toughening effects of zirconia/organic nanolaminates, Advanced engineering materials 12(9), pp. 935-941.

Li, J, Beres, W., 2006, Three-dimensional finite element modelling of the scratch test for a TiN coated titanium alloy substrate, Wear, 260, pp. 1232-1242.

Holmberg, K, Laukkanen, A, Ronkainen, H., Wallin, K., Varjus, S., 2003, A model for stresses, crack generation and fracture toughness calculation in scratched TiN-coated steel surfaces, Wear, 254, pp. 278-291.

Pandure, P., Jatti, V., Singh, T., 2014, Three dimensional FE modeling and simulation of nano-indentation and scratch test for TiN coated high speed steel substrate, International Journal of Applied Engineering Research, 9, pp. 2771-2777.

Toparlj, M., Sasaki, Sh., 2002, Evaluation of the adhesion of TiN films using nanoindentation and scratch testing, Philosophical Magazine A, 82(10), pp. 2191-2197.

Kuhl, E., Balle, F., 2005, Computational modeling of hip replacement surgery: total hip replacement vs. hip resurfacing, Technische Mechanik, 25(2), pp. 107-114.

Dickinson, A., Taylor, A., Browne, M., 2012, Implant-bone interface healing and adaptation in resurfacing hip replacement, Computer Methods in Biomechanics and Biomedical Engineering, 15(9), pp. 935-947.

Dickinson, A.S., Browne, M., Roques, A.C., Taylor, A.C., 2013, A fatigue assessment technique for modular and pre-stressed orthopaedic implants, Medical Engineering and Physics, 36(1), pp. 72-80.

Shilko, E.V., Psakhie, S.G., Schmauder, S., Popov, V.L., Astafurov, S.V., Smolin, A.Yu., 2015, Overcoming the limitations of distinct element method for multiscale modeling of materials with multimodal internal structure, Computational Materials Science, 102, pp. 267-285.

Smolin, A.Yu., Shilko, E.V., Astafurov, S.V., Kolubaev, E.A., Eremina, G.M., Psakhie, S.G., 2018, Understanding the mechanisms of friction stir welding based on computer simulation using particles, Defence Technology, 14, pp. 643-656.

Material Datasheet: TIMETAL 6-4s, Titanium Metals Corporation, 2000.

Bonello, T., Avelar-Batista Wilson, J.C., Housden, J., Gutmanas, E.Y., Gotman, I., Matthews, A., Leyland, A., Cassar, G., 2014, Evaluating the effects of PIRAC nitrogen-diffusion treatments on the mechanical performance of Ti–6Al–4V alloy, Materials Science & Engineering A, 619, pp. 300-311.

Giannakpoulos, A.E., Suresh, S., 1999, Determination of elastoplasic properties by instrumented sharp indentation, Scripta Materialia. 40(10), pp. 1191-1198.

Oliver, W., Pharr, G. M., 1992, An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments, Journal of Materials Research, 7(6), pp.1564-1583

Cheung, G., Zalzal, P., Bhandari, M., Spelt, J.K., Papini, M., 2004, Finite element analysis of a femoral retrograde intramedullary nail subject to gait loading, Medical Engineering & Physics, 26(2), pp. 93-108.

Todo, M., 2018, Biomechanical analysis of hip joint arthroplasties using CT-image based finite element method. Journal of Surgery and Research, 1, pp. 34-41.

Gerhardt, L.C., Boccaccini, A.R., 2010, Bioactive glass and glass-ceramic scaffolds for bone tissue engineering, Materials, 3(7), pp. 3867-3910.




DOI: https://doi.org/10.22190/FUME190122014E

Refbacks

  • There are currently no refbacks.


ISSN: 0354-2025 (Print)

ISSN: 2335-0164 (Online)

COBISS.SR-ID 98732551

ZDB-ID: 2766459-4